Current File : //usr/src/kernels/3.10.0-957.21.3.el7.centos.plus.x86_64/drivers/media/rc/Kconfig
config RC_CORE
tristate
depends on MEDIA_RC_SUPPORT
depends on INPUT
default y
source "drivers/media/rc/keymaps/Kconfig"
menuconfig RC_DECODERS
bool "Remote controller decoders"
depends on RC_CORE
default y
if RC_DECODERS
config LIRC
tristate "LIRC interface driver"
depends on RC_CORE
---help---
Enable this option to build the Linux Infrared Remote
Control (LIRC) core device interface driver. The LIRC
interface passes raw IR to and from userspace, where the
LIRC daemon handles protocol decoding for IR reception and
encoding for IR transmitting (aka "blasting").
config IR_LIRC_CODEC
tristate "Enable IR to LIRC bridge"
depends on RC_CORE
depends on LIRC
default y
---help---
Enable this option to pass raw IR to and from userspace via
the LIRC interface.
config IR_NEC_DECODER
tristate "Enable IR raw decoder for the NEC protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have IR with NEC protocol, and
if the IR is decoded in software
config IR_RC5_DECODER
tristate "Enable IR raw decoder for the RC-5 protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have IR with RC-5 protocol, and
if the IR is decoded in software
config IR_RC6_DECODER
tristate "Enable IR raw decoder for the RC6 protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have an infrared remote control which
uses the RC6 protocol, and you need software decoding support.
config IR_JVC_DECODER
tristate "Enable IR raw decoder for the JVC protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have an infrared remote control which
uses the JVC protocol, and you need software decoding support.
config IR_SONY_DECODER
tristate "Enable IR raw decoder for the Sony protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have an infrared remote control which
uses the Sony protocol, and you need software decoding support.
config IR_RC5_SZ_DECODER
tristate "Enable IR raw decoder for the RC-5 (streamzap) protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have IR with RC-5 (streamzap) protocol,
and if the IR is decoded in software. (The Streamzap PC Remote
uses an IR protocol that is almost standard RC-5, but not quite,
as it uses an additional bit).
config IR_SANYO_DECODER
tristate "Enable IR raw decoder for the Sanyo protocol"
depends on RC_CORE
default y
---help---
Enable this option if you have an infrared remote control which
uses the Sanyo protocol (Sanyo, Aiwa, Chinon remotes),
and you need software decoding support.
config IR_MCE_KBD_DECODER
tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
depends on RC_CORE
select BITREVERSE
default y
---help---
Enable this option if you have a Microsoft Remote Keyboard for
Windows Media Center Edition, which you would like to use with
a raw IR receiver in your system.
endif #RC_DECODERS
menuconfig RC_DEVICES
bool "Remote Controller devices"
depends on RC_CORE
if RC_DEVICES
config RC_ATI_REMOTE
tristate "ATI / X10 based USB RF remote controls"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
help
Say Y here if you want to use an X10 based USB remote control.
These are RF remotes with USB receivers.
Such devices include the ATI remote that comes with many of ATI's
All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote,
Medion RF remote, and SnapStream FireFly remote.
This driver provides mouse pointer, left and right mouse buttons,
and maps all the other remote buttons to keypress events.
To compile this driver as a module, choose M here: the module will be
called ati_remote.
config IR_ENE
tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
depends on PNP
depends on RC_CORE
---help---
Say Y here to enable support for integrated infrared receiver
/transceiver made by ENE.
You can see if you have it by looking at lspnp output.
Output should include ENE0100 ENE0200 or something similar.
To compile this driver as a module, choose M here: the
module will be called ene_ir.
config IR_IMON
tristate "SoundGraph iMON Receiver and Display"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
---help---
Say Y here if you want to use a SoundGraph iMON (aka Antec Veris)
IR Receiver and/or LCD/VFD/VGA display.
To compile this driver as a module, choose M here: the
module will be called imon.
config IR_MCEUSB
tristate "Windows Media Center Ed. eHome Infrared Transceiver"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
---help---
Say Y here if you want to use a Windows Media Center Edition
eHome Infrared Transceiver.
To compile this driver as a module, choose M here: the
module will be called mceusb.
config IR_ITE_CIR
tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
depends on PNP
depends on RC_CORE
---help---
Say Y here to enable support for integrated infrared receivers
/transceivers made by ITE Tech Inc. These are found in
several ASUS devices, like the ASUS Digimatrix or the ASUS
EEEBox 1501U.
To compile this driver as a module, choose M here: the
module will be called ite-cir.
config IR_FINTEK
tristate "Fintek Consumer Infrared Transceiver"
depends on PNP
depends on RC_CORE
---help---
Say Y here to enable support for integrated infrared receiver
/transciever made by Fintek. This chip is found on assorted
Jetway motherboards (and of course, possibly others).
To compile this driver as a module, choose M here: the
module will be called fintek-cir.
config IR_NUVOTON
tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
depends on PNP
depends on RC_CORE
---help---
Say Y here to enable support for integrated infrared receiver
/transciever made by Nuvoton (formerly Winbond). This chip is
found in the ASRock ION 330HT, as well as assorted Intel
DP55-series motherboards (and of course, possibly others).
To compile this driver as a module, choose M here: the
module will be called nuvoton-cir.
config IR_REDRAT3
tristate "RedRat3 IR Transceiver"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
---help---
Say Y here if you want to use a RedRat3 Infrared Transceiver.
To compile this driver as a module, choose M here: the
module will be called redrat3.
config IR_STREAMZAP
tristate "Streamzap PC Remote IR Receiver"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
---help---
Say Y here if you want to use a Streamzap PC Remote
Infrared Receiver.
To compile this driver as a module, choose M here: the
module will be called streamzap.
config IR_WINBOND_CIR
tristate "Winbond IR remote control"
depends on X86 && PNP
depends on RC_CORE
select NEW_LEDS
select LEDS_CLASS
select LEDS_TRIGGERS
select BITREVERSE
---help---
Say Y here if you want to use the IR remote functionality found
in some Winbond SuperI/O chips. Currently only the WPCD376I
chip is supported (included in some Intel Media series
motherboards).
To compile this driver as a module, choose M here: the module will
be called winbond_cir.
config IR_IGUANA
tristate "IguanaWorks USB IR Transceiver"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
---help---
Say Y here if you want to use the IguanaWorks USB IR Transceiver.
Both infrared receive and send are supported. If you want to
change the ID or the pin config, use the user space driver from
IguanaWorks.
Only firmware 0x0205 and later is supported.
To compile this driver as a module, choose M here: the module will
be called iguanair.
config IR_TTUSBIR
tristate "TechnoTrend USB IR Receiver"
depends on USB_ARCH_HAS_HCD
depends on RC_CORE
select USB
select NEW_LEDS
select LEDS_CLASS
---help---
Say Y here if you want to use the TechnoTrend USB IR Receiver. The
driver can control the led.
To compile this driver as a module, choose M here: the module will
be called ttusbir.
config IR_RX51
tristate "Nokia N900 IR transmitter diode"
depends on OMAP_DM_TIMER && ARCH_OMAP2PLUS && LIRC && !ARCH_MULTIPLATFORM
---help---
Say Y or M here if you want to enable support for the IR
transmitter diode built in the Nokia N900 (RX51) device.
The driver uses omap DM timers for generating the carrier
wave and pulses.
config RC_LOOPBACK
tristate "Remote Control Loopback Driver"
depends on RC_CORE
---help---
Say Y here if you want support for the remote control loopback
driver which allows TX data to be sent back as RX data.
This is mostly useful for debugging purposes.
If you're not sure, select N here.
To compile this driver as a module, choose M here: the module will
be called rc_loopback.
config IR_GPIO_CIR
tristate "GPIO IR remote control"
depends on RC_CORE
---help---
Say Y if you want to use GPIO based IR Receiver.
To compile this driver as a module, choose M here: the module will
be called gpio-ir-recv.
endif #RC_DEVICES
Mini Shell