Current File : //usr/lib/modules/3.10.0-1160.88.1.el7.centos.plus.x86_64/source/arch/x86/Kconfig.debug
menu "Kernel hacking"
config TRACE_IRQFLAGS_SUPPORT
def_bool y
source "lib/Kconfig.debug"
config EARLY_PRINTK_USB
bool
config STRICT_DEVMEM
bool "Filter access to /dev/mem"
---help---
If this option is disabled, you allow userspace (root) access to all
of memory, including kernel and userspace memory. Accidental
access to this is obviously disastrous, but specific access can
be used by people debugging the kernel. Note that with PAT support
enabled, even in this case there are restrictions on /dev/mem
use due to the cache aliasing requirements.
If this option is switched on, the /dev/mem file only allows
userspace access to PCI space and the BIOS code and data regions.
This is sufficient for dosemu and X and all common users of
/dev/mem.
If in doubt, say Y.
config X86_VERBOSE_BOOTUP
bool "Enable verbose x86 bootup info messages"
default y
---help---
Enables the informational output from the decompression stage
(e.g. bzImage) of the boot. If you disable this you will still
see errors. Disable this if you want silent bootup.
config EARLY_PRINTK
bool "Early printk" if EXPERT
default y
---help---
Write kernel log output directly into the VGA buffer or to a serial
port.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized. For normal operation
it is not recommended because it looks ugly and doesn't cooperate
with klogd/syslogd or the X server. You should normally say N here,
unless you want to debug such a crash.
config EARLY_PRINTK_INTEL_MID
bool "Early printk for Intel MID platform support"
depends on EARLY_PRINTK && X86_INTEL_MID
config EARLY_PRINTK_DBGP
bool "Early printk via EHCI debug port"
depends on EARLY_PRINTK && PCI
select EARLY_PRINTK_USB
---help---
Write kernel log output directly into the EHCI debug port.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized. For normal operation
it is not recommended because it looks ugly and doesn't cooperate
with klogd/syslogd or the X server. You should normally say N here,
unless you want to debug such a crash. You need usb debug device.
config DEBUG_STACKOVERFLOW
bool "Check for stack overflows"
depends on DEBUG_KERNEL
---help---
Say Y here if you want to check the overflows of kernel, IRQ
and exception stacks. This option will cause messages of the
stacks in detail when free stack space drops below a certain
limit.
If in doubt, say "N".
config EARLY_PRINTK_EFI
bool "Early printk via the EFI framebuffer"
depends on EFI && EARLY_PRINTK
select FONT_SUPPORT
---help---
Write kernel log output directly into the EFI framebuffer.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized.
config EARLY_PRINTK_USB_XDBC
bool "Early printk via the xHCI debug port"
depends on EARLY_PRINTK && PCI
select EARLY_PRINTK_USB
---help---
Write kernel log output directly into the xHCI debug port.
One use for this feature is kernel debugging, for example when your
machine crashes very early before the regular console code is
initialized. Other uses include simpler, lockless logging instead of
a full-blown printk console driver + klogd.
For normal production environments this is normally not recommended,
because it doesn't feed events into klogd/syslogd and doesn't try to
print anything on the screen.
You should normally say N here, unless you want to debug early
crashes or need a very simple printk logging facility.
config MCSAFE_TEST
def_bool n
config X86_PTDUMP
bool "Export kernel pagetable layout to userspace via debugfs"
depends on DEBUG_KERNEL
select DEBUG_FS
---help---
Say Y here if you want to show the kernel pagetable layout in a
debugfs file. This information is only useful for kernel developers
who are working in architecture specific areas of the kernel.
It is probably not a good idea to enable this feature in a production
kernel.
If in doubt, say "N"
config EFI_PGT_DUMP
bool "Dump the EFI pagetable"
depends on EFI && X86_PTDUMP
---help---
Enable this if you want to dump the EFI page table before
enabling virtual mode. This can be used to debug miscellaneous
issues with the mapping of the EFI runtime regions into that
table.
config DEBUG_RODATA
bool "Write protect kernel read-only data structures"
default y
depends on DEBUG_KERNEL
---help---
Mark the kernel read-only data as write-protected in the pagetables,
in order to catch accidental (and incorrect) writes to such const
data. This is recommended so that we can catch kernel bugs sooner.
If in doubt, say "Y".
config DEBUG_RODATA_TEST
bool "Testcase for the DEBUG_RODATA feature"
depends on DEBUG_RODATA
default y
---help---
This option enables a testcase for the DEBUG_RODATA
feature as well as for the change_page_attr() infrastructure.
If in doubt, say "N"
config DEBUG_SET_MODULE_RONX
bool "Set loadable kernel module data as NX and text as RO"
depends on MODULES
---help---
This option helps catch unintended modifications to loadable
kernel module's text and read-only data. It also prevents execution
of module data. Such protection may interfere with run-time code
patching and dynamic kernel tracing - and they might also protect
against certain classes of kernel exploits.
If in doubt, say "N".
config DOUBLEFAULT
default y
bool "Enable doublefault exception handler" if EXPERT
depends on X86_32
---help---
This option allows trapping of rare doublefault exceptions that
would otherwise cause a system to silently reboot. Disabling this
option saves about 4k and might cause you much additional grey
hair.
config DEBUG_TLBFLUSH
bool "Set upper limit of TLB entries to flush one-by-one"
depends on DEBUG_KERNEL
---help---
X86-only for now.
This option allows the user to tune the amount of TLB entries the
kernel flushes one-by-one instead of doing a full TLB flush. In
certain situations, the former is cheaper. This is controlled by the
tlb_flushall_shift knob under /sys/kernel/debug/x86. If you set it
to -1, the code flushes the whole TLB unconditionally. Otherwise,
for positive values of it, the kernel will use single TLB entry
invalidating instructions according to the following formula:
flush_entries <= active_tlb_entries / 2^tlb_flushall_shift
If in doubt, say "N".
config IOMMU_DEBUG
bool "Enable IOMMU debugging"
depends on GART_IOMMU && DEBUG_KERNEL
depends on X86_64
---help---
Force the IOMMU to on even when you have less than 4GB of
memory and add debugging code. On overflow always panic. And
allow to enable IOMMU leak tracing. Can be disabled at boot
time with iommu=noforce. This will also enable scatter gather
list merging. Currently not recommended for production
code. When you use it make sure you have a big enough
IOMMU/AGP aperture. Most of the options enabled by this can
be set more finegrained using the iommu= command line
options. See Documentation/x86/x86_64/boot-options.txt for more
details.
config IOMMU_STRESS
bool "Enable IOMMU stress-test mode"
---help---
This option disables various optimizations in IOMMU related
code to do real stress testing of the IOMMU code. This option
will cause a performance drop and should only be enabled for
testing.
config IOMMU_LEAK
bool "IOMMU leak tracing"
depends on IOMMU_DEBUG && DMA_API_DEBUG
---help---
Add a simple leak tracer to the IOMMU code. This is useful when you
are debugging a buggy device driver that leaks IOMMU mappings.
config HAVE_MMIOTRACE_SUPPORT
def_bool y
config X86_DECODER_SELFTEST
bool "x86 instruction decoder selftest"
depends on DEBUG_KERNEL && KPROBES
---help---
Perform x86 instruction decoder selftests at build time.
This option is useful for checking the sanity of x86 instruction
decoder code.
If unsure, say "N".
#
# IO delay types:
#
config IO_DELAY_TYPE_0X80
int
default "0"
config IO_DELAY_TYPE_0XED
int
default "1"
config IO_DELAY_TYPE_UDELAY
int
default "2"
config IO_DELAY_TYPE_NONE
int
default "3"
choice
prompt "IO delay type"
default IO_DELAY_0X80
config IO_DELAY_0X80
bool "port 0x80 based port-IO delay [recommended]"
---help---
This is the traditional Linux IO delay used for in/out_p.
It is the most tested hence safest selection here.
config IO_DELAY_0XED
bool "port 0xed based port-IO delay"
---help---
Use port 0xed as the IO delay. This frees up port 0x80 which is
often used as a hardware-debug port.
config IO_DELAY_UDELAY
bool "udelay based port-IO delay"
---help---
Use udelay(2) as the IO delay method. This provides the delay
while not having any side-effect on the IO port space.
config IO_DELAY_NONE
bool "no port-IO delay"
---help---
No port-IO delay. Will break on old boxes that require port-IO
delay for certain operations. Should work on most new machines.
endchoice
if IO_DELAY_0X80
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_0X80
endif
if IO_DELAY_0XED
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_0XED
endif
if IO_DELAY_UDELAY
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_UDELAY
endif
if IO_DELAY_NONE
config DEFAULT_IO_DELAY_TYPE
int
default IO_DELAY_TYPE_NONE
endif
config DEBUG_BOOT_PARAMS
bool "Debug boot parameters"
depends on DEBUG_KERNEL
depends on DEBUG_FS
---help---
This option will cause struct boot_params to be exported via debugfs.
config CPA_DEBUG
bool "CPA self-test code"
depends on DEBUG_KERNEL
---help---
Do change_page_attr() self-tests every 30 seconds.
config OPTIMIZE_INLINING
bool "Allow gcc to uninline functions marked 'inline'"
---help---
This option determines if the kernel forces gcc to inline the functions
developers have marked 'inline'. Doing so takes away freedom from gcc to
do what it thinks is best, which is desirable for the gcc 3.x series of
compilers. The gcc 4.x series have a rewritten inlining algorithm and
enabling this option will generate a smaller kernel there. Hopefully
this algorithm is so good that allowing gcc 4.x and above to make the
decision will become the default in the future. Until then this option
is there to test gcc for this.
If unsure, say N.
config DEBUG_NMI_SELFTEST
bool "NMI Selftest"
depends on DEBUG_KERNEL && X86_LOCAL_APIC
---help---
Enabling this option turns on a quick NMI selftest to verify
that the NMI behaves correctly.
This might help diagnose strange hangs that rely on NMI to
function properly.
If unsure, say N.
endmenu
Mini Shell